الأحد، 27 مارس 2016

DIY SOLAR PV PANEL INFORMATION


 EmailPrint
No image
Here are collected notes and ideas on building your own solar photovoltaic (PV) panel. These come from a number of places including attending a course run by Dan Quiggin of Demand Energy Equality, web-searching, discussion with Norman Phipps of Handmade Solar and also running my own DIY PV workshop at Nottingham hackspace.
I feel that the process of making a solar PV panel is very informative and interesting. Making solar PV panels cheaper than those available is quite difficult, due to mass manufacture production methods and the use of cheaper labour. Also encapsulation is a major issue  - without correct encapsulation then there might be issues with moisture and degradation of the surface of the cells.

DIY PV courses

Here is a list of people and groups running courses or providing information on building your own solar PV panel:

Suppliers of equipment

These are suppliers of equipment that I have heard about or have used:

Basic construction process

I have called this a DIY PV panel, but in reality this would be very hard to fully create every component within the PV module using a DIY process. There are a number of elements within the PV module:
  • Glass
The glass used in solar PV modules is low-iron oxide glass. This has very good transmissivity properties. Glass used for windows generally block UV light and which reduces the efficiency of the finished panel if used in a DIY solar panel. Obviously low-iron glass is harder to come by. I used 4mm window pane glass for my PV panels as it was very cheap and easy to come by.
Actually making your own glass is obviously very difficult and has a very high enegy cost. For a DIY solar panel it makes energy and environmental sense to re-use window pane glass.
  • Photovoltaic (PV) cells
The main part of the solar PV panel. DIY solar PV panels use reject or slightly damaged PV cells from large PV producers. Making your own DIY mono or poly crystalline would be almost impossible due to the energy requirements and the fact they must be produced in extremely clean environments. Cutting the cells into thin wafers (generally 100um thick) requires production techniques.
  • Wire interconenctions (called tabbing wire)
 To make good connections, correct tabbing wire should be used. It is not expensive to buy.
  • Encapsulant
Commercial solar PV modules use special silicone encapsulant. This protects the cells from moisture ingress and also from minor vibration damage as the cells are extremely fragile. This option is available to the DIYer (check the video in this post) but is the correct encapsulant is quite expensive to buy, especially in small quantities.
  • Metal frame
 Most commercial PV modules have an aluminium frame. This is for mechanical protection and for helping to mount the modules. This is potentially not required for DIY modules. Also re-cycled aluminium angle could be used. I used 4mm thick glass and was only making quite small modules, so frames were not required.

PV Cells

The majority of DIY PV modules use broken or rejected crystalline silicon solar cells. Here are some broken pieces from a large manufacturer. Due to the fragile nature of the cells, most PV manufacturers have rejects, which are usually re-processed as they are produced from very high purity silicon. Obviously this comes at a high energy cost and if they can be sensibly used in DIY modules then it is probably better from an environmental point of view.
No image
A selection of randomly sized broken cell fragments. The output voltage of a cell even a very small piece will be the same (around 0.6V) but the output current will be totally dependant upon the surface area.
No image
This is a pack of full and almost full cells. They might have been rejected by the manufacturer due to some cosmetic defect or very small chip.

Cutting PV cells

Cutting the PV cells would be a good idea to do so that the modules are more even and we can fit more PV cell area into a give space. The various random sized pieces could all be made into relatively standard pieces and hence make it easier to wire together. It would also help standardise the tabbing connections.
It is difficult to cut a crystalline cell, as they have a tendency to shatter as they are very thin and fragile. Here are some videos of processes to cut the cells. Most use a diamond cutting disk and a rotary tool (such as a Dremel etc). I tried this by hand but the cells can still shatter, hence you also need some form of jig to hold the rotary tool.
I built a jig holding a Dermel tool and that cut the cells, but it was still a difficult process which left a slightly jagged edge. This is something that I still need to work on.
Update 8/11/12: I was lent a diamond tipped tile cutter from a member of the Nottingham Hackspace. This uses a water bath. The cut was pretty good - it was still a little bit jagged, but much better than any other method I had tried so far. Here is a short clip of cutting in action:

Wiring PV cells

PV cells are wired together using tabbing wire. This is soldered onto the front and back of each cell, which are the two electrical connections to the cell. A high powered soldering iron is used along with additional flux from a flux pen. The tabbing wire already has solder on it and the flux ensures that a good electrical connection is made. Once soldered then check with a multimeter to see which side is positive and which is negative and also that the cell is functioning correctly. Each PV cell only generates around 0.6V DC so cells are wired in series to give higher voltages. For a PV module for a 12V lead-acid battery you will need 36 cells wired in series.
No image
Tabbing wire on a cardboard reel and a flux pen.

Encapsulating PV cells

I wss very interested in encapsulating the cells. I bough this silicone QSIL 216 from Know Your Planet. It is a 2-part liquid silicone which sets very (amazingly) clear. Here is a short video showing one of the first encapsulations to give an idea of the process and the consistency:
The end result of this process is shown here:
No image
This is the end result of the PV panel build. There are 12 cells ins series, each giving around 0.6V, so output will be in the region of 7V.
No image
All of the cells has some air bubbles. Next time I would put a thin layer of silicone down then push the cells into it, rather than let it pour around.
No image
This was the worst cell for bubbles - there is a large air gap. But it is all sealed, so moisture cannot enter.
No image
The back of the module - no bubbles here.
No image
There are blobs on the back and points where the tabbing wire sticks through the silicone, which is not good. I have patched that up with silicone sealant.
No image
This module was designed to output 7V under bright light. It outputs 5V on the desk in my office, which is OK, but needs more testing.

http://www.re-innovation.co.uk/web12/index.php/en/information/solar-pv-information/diy-solar-pv

ليست هناك تعليقات:

التعليقات

بحث هذه المدونة الإلكترونية